X350RRiding Lawn Equipment

14.1-kW at 3100 rpm V-twin engine

The tractor is powered by an iTorque power system, a combination of engine features, and an exclusive hood design that provides superior lugging ability, even cooling, and durability.
 
A large 726-cc (44.3-cu in.), 14.1-kW engine at 3100 rpm has plenty of power and torque for superior performance. The larger, more powerful engine also allows the engine to be operated at a lower 3100-rpm speed for quieter operation.

Key engine features include:

• 14.1 kW at 3100 rpm
• Large 726-cc (44.3-cu in.) displacement
• Quality features include:
  • Cast-iron cylinder liner
  • Overhead valve
  • Full-pressure lubrication
  • Replaceable oil filter
  • Dual-stage air cleaner
• V-twin design:
  • Excellent power and performance
  • Easy starts
  • Smooth operation

Flywheel alternator

A flywheel alternator provides plenty of capacity to quickly recharge the battery and power electrical equipment, such as lights or a sprayer:

• 12-amp charging capacity
• Regulated to keep the battery at full charge without risk of overcharging

Fuel tank has large, conveniently located fill opening

Large fuel-fill opening

Large, 7.6-cm (3-in.) diameter fuel tank filler opening makes adding fuel easy:

• Located on the left fender
• Helps eliminate spillage
• 7.6-L (2-U.S. gal.) capacity
• Low fuel light on dash warns the operator when fuel level is getting low

107-cm (42-in.) Rear-Discharge Mower Deck

X350R 107-cm (42-in.) Mower Deck

The innovative design of the 107-cm (42-in.) Edge™ Rear-Discharge Deck combines the best features for reliability and superior performance when mowing, collecting, and mulching grass and leaves:

• The mower deck is stamped from 11-gauge, 3-mm (0.120-in.) steel to provide smooth contours for a quality appearance and excellent performance.
• Easy to install or remove mulch plug is included as standard equipment.
  • The included AM147289 blades provide optimal collection/rear discharge and good mulching results in many conditions. For optimal mulching, AM140332 mulching blades are available.
• With no side-discharge chute, the mower can trim on either side for mowing efficiency and convenience.
  • A smaller storage area requirement is an additional benefit.
• A standard V-belt and non-timed blade design gives superior reliability and trouble-free operation.
• Offset mower blades permit blade overlap with the use of a standard V-belt drive.
  • The blades cut cleanly without being able to contact each other.
• A heavy-duty V-belt and large spring-loaded idler pulley transfer power to the mower blades efficiently and reliably.
• Three mower wheels help level the mowing job and reduce the chance of scalping the lawn.
• Cut-height increments of 0.64 cm (0.25 in.) allow for operating the mower at the optimum cutting height.
• A quick-adjust deck-leveling system is provided to make keeping the deck properly adjusted easy.

Contoured deck and discharge blade, 92-cm (36-in.) mower for X135R shown

The mower deck is contoured and free of obstructions to ensure optimum cutting and bagging performance:

• Grass clippings flow smoothly around the deck and up the chute into the hopper.
• Clipping buildup is minimized to ensure continued high-performance and easy cleanup.
• Special discharge blades (standard equipment) have a large wing to propel grass clippings up the chute and into the hopper.
• Mower fills and packs the 300-L hopper with a large volume of grass clippings and/or leaves.

Standard mulch plug

Standard mulch plug

Mulch plug easily installs in place of hopper:

• A mulch plug is included with the model year 2017 and later X350R as standard equipment (SN 20,001-).
• Mulch plug is ideal for times when collecting grass clippings and leaves is not desired. The rear hopper can be easily removed and the mulch plug installed.
• Plug closes off opening on bottom of deck so material cannot enter the chute.
• The included AM147289 blades provide optimal bagging and rear discharge performance and good mulching results in many conditions.
• For optimal mulching, AM140332 mulching blades are available.

Wash port

Hose-end adapter example shown can be purchased locally - not standard equipment

Wash ports are provided on each side of the mower deck. They can be used to supply water to the underside of the deck so it can be easily cleaned after use:

• Wash ports are designed for hose quick-connect fitting.
• Connect hose to the wash port on one side of the mower at a time and operate the mower to clean.
• Using the wash ports cleans bottom of deck and chute.
• Wash ports work best if used immediately after the mowing job is completed.
• Operating the mower deck while the water is running removes grass clippings.
• Use of the wash ports prevents buildup of material from affecting performance the next time the mower is used.

A hose-end adapter for the appropriate water hose to be used can be purchased locally for connection to the wash ports.

Optional rear deflector

Optional rear deflector in operation

Optional rear deflector (BM25065) easily installs in place of hopper:

• No tools required for installation
• Deflects clippings in an even pattern behind the tractor

Hopper easily emptied from operator seat

Long handle gives good leverage

Durable 300-L (8.5-bu) hopper empties completely

The innovative design of the rear hopper sets a high standard for collecting systems:

• Hopper is constructed of durable fabric for flexibility, where needed.

Hopper shipping

Hopper is nested in tractor for efficient shipping

Large-capacity hopper

• Minimizes shipping cost
• No extra carton material, which reduces disposal cost

Hopper is made of durable materials and sealed to keep dust away from the operator.

High-quality steering system for easy operation

X350R is designed for easy turns

A heavy-duty sector and pinion steering system with quality bearings provides easy and precise control for the life of the tractor:

• Tight turning radius of 42 cm (16.5 in.) provides good maneuverability.
• Easy steering promotes mowing efficiency and operator comfort.

Easy steering

Easy steering is important to give the operator an enjoyable mowing experience:

• Larger, 36-cm (14-in.) diameter steering wheel gives good leverage for easy turns.
• Larger sector gear gives improved (increased) steering ratio.
  • Higher steering ratio results in less effort to turn the wheel.
• Ball-joints on both ends of the steering tie rod and drag link maintain accurate steering longer.
• Long steering drag link improves mechanical advantage of the steering system through the full range of motion.
• Sector gear pivots on a shaft rather than a bushing.
  • This ensures proper gear mesh and eliminates binding to result in easier steering.
• Greaseable front steering spindles reduce friction and improves wear through time.

Kanzaki® K46 transaxle

The Tuff Torq® hydrostatic transaxle encloses the hydrostatic pump and motor rotator groups in the same housing with the differential and axle housings:

• This very efficient design reduces the number of sealing surfaces and minimizes potential for leakage.
• The transaxle is essentially the same as the one used in the X300 Tractor; however, it is reversed, and the drive linkage is unique to work with the rear-discharge system.

When combined with the foot controls, the hydrostatic transmission functions similarly to an automatic transmission in an automobile, so the term automatic is often used to describe it:

• Use of the latest valve designs has significantly reduced the sound level.
• Large pump and motor rotating groups ensure efficient operation and long life.

Free-wheeling valve

Convenient free-wheeling valve

The free-wheeling valve control is located near the tractor rear hitch plate for good visibility and easy operation.

Kanzaki and Tuff Torq are trademarks of Kanzaki Kokyukoki Mfg. Co., Ltd.

Operator station

Display panel

The contoured dash has clean, attractive styling and ergonomic controls for easy use:

• Controls are color-coded for easy identification by the operator.
• Controls are logically placed and easy to reach.
• The power take-off (PTO) switch allows the operator to get fingers underneath it, like a T-handle, to pull up for easy activation.
• The reverse implement option (RIO) switch is an easy to see and use yellow button.
• To simplify snow blower operation, RIO can be activated with the same hand that lifts or latches the snow blower.
• The latch control for foot lift and the park brake latch are pivot levers for low effort.
• Cruise control activation is handled by an automotive-style button.
• Separate engine speed and choke controls make starting and warming up the engine easier in cold weather.
  • The choke lever is spring loaded to eliminate the chance the tractor will be unintentionally operated with the choke partially closed.
• Functional design of the throttle and choke controls provides good appearance and a comfortable feel.

		A — Caution / stop		G — Service
		B — Power take-off (PTO)		H —Engine speed
		C — Battery charge status		I — Engine speed symbol
		D — Park brake		J —Best cut range
		E — Operator presence		K —Material collection system (MCS)
		F — Hour meter		L - Low fuel

Display has the look and feel of a modern automobile. A power-up sequence cycles lights and gauges to indicate they are working:

• Display features dark-cockpit design to minimize operator distractions.
• Display is back lit for night visibility.
• Night visibility is especially useful with snow blower use.
• When the hopper is full, the hopper-full light comes on and the tractor power take-off (PTO) automatically shuts off.
• Hour meter makes it easy to tell when oil changes and other maintenance should be performed.
• Low fuel light provides the operator with a noticeable warning when low on fuel.
• A tachometer graphically displays engine speed.
  • Target-zone graphics inform the operator of the engine speed range to use for best cut quality.
• An indicator tells the operator when the PTO is operating.
• Bright caution and stop lights capture the operator's attention when important information is on the instrument cluster.
  • Damage can be prevented and repair costs reduced by addressing problems early.
• Operators are advised of what the problem is if they attempt to operate the mower with unsatisfied PTO, seat, or park brake interlocks.
• The indicators are also useful to identify the reasons the PTO or engine may have shut off when an interlock is unsatisfied.
• Operators are advised if battery voltage is low, normal, or excessive.
• The service indicator light illuminates to indicate a diagnostic error code is stored.
• On-board diagnostics provides trouble codes for use by trained technicians.
  • For example, a technician will be able to test switch functionality and circuit continuity without tools.

Foot-pedal lift system

Foot-pedal lift system

Pushing with the foot to raise the mower or implement is less strenuous for many operators:

• The easy-to-use raised position lock operates similarly to the park brake lock.
• The foot pedal is out of the way and not likely to catch on bushes and tree limbs when mowing.
• The mower deck returns to same preset height each time it is lowered.
• A lift-assist spring is provided to minimize lift effort.
  • An optional BM24810 supplemental lift-assist spring kit (X350R) is required for snow blower use.
• The mower will not be inadvertently locked in the raised position when mowing through ditches.
  • When installing or removing a mower or front equipment raised by the foot lift system, spring tension may be removed from the connection points by pulling rearward on the lift pedal and raising the lift latch to hold the pedal in the rearward position.

Twin Touch™ foot control is easy to use and has cruise control

Twin Touch foot control

Cruise-control button on the dashboard

Twin Touch foot pedals control the speed and direction of travel:

• Automotive-type accelerator control ensures easy operation.
• Operator can change direction without lifting foot off the platform.
• Large pedal surface gives superior operator comfort.

Cruise control

Cruise control is standard equipment:

• To engage, push the cruise button and hold until the foot is removed from the forward pedal.
• For emergency stop, the cruise control can be released by pushing on the brake pedal or the forward pedal.

Mower deck height adjustment

Mower deck height adjustment

Rotary dial knob makes adjusting mower cut height quick and easy:

• Provides mower cut heights in 0.6-cm (0.25-in.) increments from 2.5 to 10.2 cm (1 to 4.0 in.)
• Mower deck returns to same preset height each time it is lowered
• Onboard deck-leveling gauge and Exact Adjust tool conveniently located in the storage compartment under the seat
  • Used in conjunction with Exact Adjust ports for easy and accurate leveling of the mower deck for optimum mowing performance

Optional supplemental lift-assist spring

Supplemental lift-assist spring kit parts

An optional supplemental lift-assist spring is available:

• Required for snow blower use.

Parking brake control

Parking brake

Depressing brake pedal applies internal wet-disk brakes (increased durability and longer life) for safe stopping.

Parking brake control is conveniently located for easy access; holds brake pedal securely in locked position.

Electric PTO clutch is easy and convenient to use

Electric PTO switch

A heavy-duty electric PTO clutch is controlled by a convenient dash-mounted switch.

Adjustable fill switch activates an indicator and alarm. The fill switch does not shut off the mower deck so the operator can choose to finish a pass.

Heavy-duty PTO clutch

PTO clutch

The PTO clutch is designed to operate through many on/off cycles.

RIO and interlock switches promote safe operation

RIO control

Mowing while backing up is strongly discouraged.

An operator who deems it necessary and chooses to keep the mower engaged while backing up, must bring the vehicle to a stop, then lift and hold the power take-off (PTO) switch in the reverse implement position as the reverse pedal is depressed slightly. The operator can then release the PTO switch and the mower will continue to operate.

This procedure must be repeated the next time the operator chooses to keep the mower (or other PTO-operated equipment) engaged while backing up.

Interlock switches

Switch senses if hopper is installed

A switch senses if the hopper (or rear deflector option) is installed. If the hopper (or rear deflector option) is not installed and the PTO switch is actuated, the PTO will not operate.

A brake interlock switch is provided so the tractor will not start unless the brake is depressed or the parking brake set.

A tractor seat switch will turn off the PTO if the operator leaves the tractor seat; it will also shut down the engine if the park brake is not set and the operator leaves the seat.

Either the operator needs to be in the seat or the hopper or deflector need to be installed for the engine to run.

Heavy-duty frame

Steel front side of hopper bolted to frame

The frame is made of heavy-formed and welded steel, reinforced in critical areas for even greater strength.

The steel front side of the hopper is bolted to the rear of the tractor frame:

• Reinforces the frame and provides a solid support for the hopper
• Frame formed from 12-gauge, 2.66-mm (0.105-in.) thick material
• Standard front bumper formed from 3.8-mm (0.15-in.) steel to complete the frame assembly

Standard rear hitch for tow-behind equipment

A standard rear hitch is included for pulling tow-behind equipment. Simply lift off the hopper and the hitch is ready to use.

Front axle and wheel spindles are heavy-duty

Cast-iron front axle

Front axle is made of nodular cast iron:

• Cast-iron front axle is strong and shock resistant.
• Cast iron will not yield under heavy loads or impact.

Replaceable bushings are used at the front axle pivot and steering spindles of models with power steering:

• Bushings provide excellent wear resistance.
• Grease cavity between the bushings maintains lubrication and easy steering between greasings (X370).
• Grease fittings at each spindle are easy to service.

Front steering spindles

Steering spindle

Front steering spindle diameter is 19 mm (0.75 in.) for strength and long life:

• Have strength to handle heavy implements
• Provide long life at bearing surfaces
• Use sealed, precision bearings in front wheels

Attractive styling

Hood air-intake louvers

Smooth, rounded contours present a modern, stylish appearance:

• Hood styling incorporates efficient full-length air-intake louvers on each side, rather than on the top, for cooler engine operation and lower operator station sound levels.
• Hot air is vented out the front grille, away from the operator.
• The fully enclosed hood is made of molded-in-color material.
  • Reduces sound
  • Will not rust or dent
• Distinctive grille and large, one-piece fender deck complete the styling package.

Two headlights give excellent visibility

Optimum lighting pattern

Headlight lens

Headlights are standard equipment:

• Two 27-W bulbs provide excellent lighting for improved visibility during evening operation.
• A headlight position on the ignition switch makes it easy to operate the headlights.
• Headlights are designed to provide an optimum lighting pattern for mowing.

Comfortable operator station

Operator station

The operator station is designed for operator comfort and ease of using controls:

• A large, 36-cm (14-in.) diameter, steering wheel is comfortable to use and minimizes steering effort.
• Full-length foot mats provide comfort for the operator and protect the footrest area.

Comfortable seat

Comfortable open-back seat

An open-back, 38-cm (15-in.) high-back seat provides a comfortable, smooth ride and good support for the operator:

• Seat travel of 17 cm (6.6 in.) with 15 positions allows the operator to be seated comfortably and easily operate the controls.
• Seat can be easily adjusted fore and aft by the operator while sitting on the seat.
• Open-back design allows air circulation to keep the operator's back cool and dry for a more comfortable ride.
• Grasp at the top of the seat is conveniently located for use when tilting the seat up to protect it from the weather.

Adjustable seat suspension

Seat suspension with springs in rear position

Seat suspension with springs in forward position

The seat suspension is adjustable, without tools, for the weight of the operator:

• Springs are adjustable fore and aft to any of three positions.
  • No tools required
  • Allows fine tuning of the suspension for the operator's weight
  • Back position for more support for heavier operators
• Tool tray is designed into the seat base.
  • Can be used to store gloves, small tools, etc.
  • Convenient storage location for Exact Adjust wrench and gauge

Cup holder and toolbox

Cup holder and covered toolbox on fender

Covered toolbox with open cover

A cup holder and toolbox are located on the fender for operator convenience:

• The cup holder holds a variety of container sizes.
• Toolbox provides convenient storage.
• Cup holder and toolbox are constructed of durable acrylonitrile butadiene styrene (ABS) plastic.

12-Vtfast connector

Fast connector location

A mid-vehicle, 12-V fast connector, located under the tractor’s fuse box, is included as standard equipment to reduce initial installation time for some attachments that operate on 12-V power from the tractor:

• The four-cavity connector includes battery, ground, and key switch terminals and is turned on and off with the ignition switch.

Hopper adjustment and removal

Adjustable hopper latch

Hopper is easily removed and reinstalled

Hopper latch is easily adjustable for operator preference and conditions:

• Spring can be located in any of three holes.
• More latching effort is required for hilly or rough operating conditions.

The hopper is easily removed by using the rear handle to raise the back end of the hopper 25 degrees, or about 13 cm (5 in.), and then using both handles to lift the hopper vertically out of the notches:

• No tools are required.
• There is nothing to disconnect.

Hopper removed

Chute shown pulled out part way

Chute is easily removed and cleaned if necessary

The chute can be easily pulled out and removed:

• Chute must be at least partially pulled out before removing the mower deck.
• Removing the chute makes cleaning easy.

Exact Adjust ports and onboard deck-leveling gauge make precise deck adjustments easy

Deck-leveling gauge and hex adjusting tool stored under tractor seat

Exact Adjust access holes

A mower deck must be level side to side and properly adjusted front to rear to give the best cutting performance. A removable, onboard deck-leveling gauge and a hex-key tool are provided to make adjustment easy:

• Gauge and hex-shaped tool conveniently located under the tractor seat in a special storage location.
• Exact Adjust leveling ports are provided on each side of the operator platform above the mower-level adjusting bolts. With the hex-shaped tool, they provide convenient access to allow quick and easy adjustment of the mower for the best quality of cut.

The Exact Adjust feature is standard on all Select Series™ X300 and X500 Tractors:

• There is no need to reach under the fender deck while making the mower-level adjustment.
• On-board deck-leveling gauge, Exact Adjust ports, and the hex tool work together.
  • Level the mower deck side-to-side
  • Set the correct amount of rake (front-to-back deck orientation)
  • Calibrate the cutting height to the cut-height adjusting knob setting
• Exact Adjust simplifies leveling the mower deck if equipped with a Power Flow™ blower.
  • To give the best cut, mower level should be adjusted if alternately mowing with and without blower installed. The Exact Adjust feature makes this easy.

Deck-leveling tool placed under deck

Using included ball-hex tool to level mower deck

Consult the operator's manual for the correct adjusting procedures for each tractor model. Basic adjusting steps to properly level the mower deck include:

• Park the tractor on a level surface.
• Inflate tires to the correct pressure.
• Consult the label for the cutting-height knob that is located on the console of the machine. This label shows deck-leveling position and location of deck-leveling adjustment points.

Cut height adjusting knob

• Set mower cutting-height knob to the correct deck-leveling position of 6.4 cm (2.5 in.)
• Adjust mower wheels as necessary so they do not contact the ground surface.
• Remove the onboard deck-leveling gauge that is located under the seat.
• Using the Exact Adjust ports and tool, adjust mower deck side-to-side level so the deck-leveling gauge just slips under the left and right lower deck rim at the designated adjustment points.
  • Left-rear and right-rear adjustment points are under the deck rim near the corners of the deck.
• Adjust mower deck front-to-back level, if necessary.
  • Loosen rear nuts equally on each side of front lift rod.
  • Turn front nut equally on each side clockwise to raise front of mower or counterclockwise to lower it until gauge just slips under the front adjustment point.
    • Front adjustment point is under the front center of the deck.
  • Tighten rear nuts after adjustment is complete.
• Return the gauge to its storage position. 

NOTE: The adjusting tool supplied with the tractor is an 8-mm (0.31-in.) ball-hex key, part number M162737. The rounded end allows for some misalignment with the bolt as the deck is adjusted.

X500 Series Tractor moving snow with the front blade

This durable blade serves as a perfect solution for snow removal and other materials.

It is very easy to mount on the tractor which facilitates all year-round usage through the different seasons. To use it, the operator simply pushes a lever from the seat and the blade lowers to the ground. When the task is complete, pulling back the lever will raise it.

Front blade angled to the left

The working angle can be changed with a lever from the tractor. This will be especially appreciated in tighter areas when frequently changing direction between left and right.

Clean to the edge with the wide blade

Clearing off snow

The blade is wider than the tractor to ensure the tractor has good traction on the cleared path and does not compact snow. Even with an angled blade, the operator can clean up to the edge of walls and other obstacles for best results.

Resist impacts and stay comfortable even when hitting obstacles hidden under snow

Demonstration of the unique safety joint: the tractor is slowed down after the impact yet can move enough to reduce the shock on the operator. The blade moves away from the obstacle by moving up.

Compatibility and required mounting hardware

Quick-hitch

Tractor-specific mounting frame

A John Deere dealer can identify which models are compatible with this broom and order the required mounting hardware.

Function of a traditional blade (upper line) and the unique safety joint (lower line):

1. Pivot point
2. Hard obstacle
3. Snow

Many front blades available in the market tilt around a pivoting point close to the ground (see 1.1). When potentially contacting an obstacle (see 1.2), the pivoting blade can barely move at all, increasing impact on the blade, tractor, and operator even more (1.3).

The unique joint solution of this blade is smarter by pivoting around a higher spot (2.1). It avoids a harsh impact as the colliding blade edge moves clearly to the rear (2.2), allowing the tractor to slow down more smoothly. Also, the blade will move up if too much snow is present – and even continues to clear off the snow. Once the hard object is overcome, the spring pushes the blade back to the original position. This all results in more comfort of the operator, better uptime of the blade and tractor together with cost effective snow removal without backing up and rehitting the obstacle attempting to clear snow on it.

Attaching to the tractor in three seconds

Three simple steps to mount the blade

To attach the blade to the tractor, simply raise it from ground, hook it into the quick-hitch, and lock it. Although it can stay on, taking the mower deck off and using rear wheel weights on the tractor is recommended. For snow applications, snow chains are suggested. Both the weights and the chains are available through John Deere Parts.

Further blades, brooms, and snow throwers

Broom and blade with quick-hitch

The following chart shows the available options for John Deere Riding Lawn Equipment and suggests which solution might be the best in each case. The entire description above applies to the blade with 125-cm (49-in.) quick-hitch. If the tractor is equipped with driveline and corresponding quick-hitch, a tractor with this quick-hitch can carry either the blade or the 120-cm (47-in.) broom.

Front broom with debris catcher on X300 Series Tractor

This broom serves as perfect solution for snow and dirt removal. It is very easy to mount and comes with a debris catcher box and multipurpose brush.

To engage, the operator simply pushes a lever from the seat and the broom lowers to the ground while starting to spin. When the job is complete, pulling back the lever will stop the broom and raise it from ground.

Front broom angled to the left

From the tractor, the working angle can be changed just by pulling or pushing the (left) lever. This is particularly beneficial in tighter areas when the frequency of changing between working to left and right is higher.

Use the debris catcher for dirt removal

Every broom is shipped with a debris catcher for when collection is required. An upper and a lower rubber lip minimize dust accumulation. To empty, tilt in from its mounted position or take it off and push on its wheels to empty the debris elsewhere.

Optimize cleaning results by adjusting ground pressure

To achieve optimal performance, the ground pressure can be increased by simply turning a knob on top of the broom. Lowering ground pressure will reduce friction and increase lifetime of the broom.

Clean to the edge and on uneven terrain

The wide broom and the central drive system clean to the very edge of walls and other obstacles. Cleaning uneven surfaces is easy and efficient; the brush itself is mounted with an oscillating bearing to compensate undulations.

Further blades, brooms, and snow throwers

Broom and blade with quick-hitch

The following chart shows available options for the John Deere Riding Lawn Equipment and suggests which solution might be the best in each case. The entire description above applies to the broom with quick-hitch 120 cm (47 in.). The 125-cm (49-in.) blade can be mounted on the same hitch as the broom and might be an excellent response to stronger snowfall.

Easy transport and storage

The air-filled caster wheel supports the broom and also allows easy moving and storing of the broom when not in use. The rubber boot over the wheel’s king pin protects it from thrown up dirt.

Attaching to the tractor in three seconds

Lift, settle, and lock the broom

To attach the broom to the tractor, simply raise it from ground, hook it into the quick-hitch, and lock by pushing the handle down. Using rear wheel weights on the tractor is recommended. For snow applications, snow chains are suggested. In some conditions it may be recommended to take off the mower deck to keep enough clearance between tire chains and deck. Both the weights and the chains are available through John Deere Parts.

Compatibility and required mounting hardware

Quick-hitch with lift lever and (tractor specific) mounting frame and driveline

A John Deere dealer can identify which models are compatible with this broom and order the required mounting hardware.

Add-on parts

Required to use a front blade.

Compatibility Information

SAB10035

For X350, X354, X370, X380 and X350RTractors. Not compatible with French compliance kit.

Driveline parts

Necessary to use a rotary broom with the machine.

Compatibility Information

SAB10037

For X350, X354, X370, X380, and X350R Tractors. Not compatible with French compliance.

Quick hitch

The front quick hitch with drive increases tractor versatility.

Compatibility Information

SAB00922

For LR135, LR175, X110, X120, X125, X130R, X135R, X140, X145, X155R, X165, X300, X300R, X304, X305R, X320, X534, and X540 Tractors. Required for SAB00726 rotary broom.

Increases machine versatility.

Compatibility Information

SAB00720

For X120, X125, X135R, X140, X145, X155R, X165, X300, X300R, X304, X305R, X320, X534, and X540 Tractors.

7P Poly Utility Cart

Every John Deere customer who owns a riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes.

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak™ or ZTrak™ mower not to exceed 250 lb (113 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck.

7P Poly Utility Cart

• Cart has a premium molded, high-density polyethylene box construction.
• Compression molding process allows polyethyl­ene to be the optimum thickness in all areas for superior strength and durability.
• Polyethylene body will not rust or dent; it stays looking new longer.
• 0.75-in. (2-cm) x 2-in. (5-cm) stake pockets are molded in to make the addition of side extensions easy.
• Two vertical 0.75-in. (2-cm) molded channels on each side allow easy use of dividers to separate the box into two or three compartments.
• Ribs in the box bottom add strength and prevent the shovel from hitting bolts when emptying the cart.
• Sloped tailgate design makes emptying the box easier; there is no tailgate to loosen or remove.
• Styling is compatible with other John Deere equipment.
• Pneumatic tires provide turf tread for good flotation, shock absorption, and minimal rolling resistance.

Wheels

17P Utility Cart wheel shown

Wheels are mounted on a solid, one-piece axle for durability.
 
Iron and Oilite® wheel bearings with grease fittings provide lubrication for long life.

The pneumatic tires offer the following:

• Good flotation
• Minimal rolling resistance
• Shock absorption

Sloped tailgate

Sloped tailgate for easy emptying

A sloped tailgate design makes emptying the box easier; there is no tailgate to loosen or remove.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

7P Poly Utility Cart
Order number: MCZLP2193500

Tractor hitch

Spring-pin tractor hitch

A large-diameter hitch pin provides plenty of strength:

• Fast, easy attachment to the tractor hitch
• Spring pin to ensure the pin stays in place

Tilt latch

Tilt latch

An easy-to-use spring-loaded dump latch allows tilting the box for easier unloading. Steep dump angle makes emptying the cart easier.

Specifications

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower not to exceed 113 kg (250 lb).
**High-density polyethylene is compression molded for optimum thickness in all areas and maximum durability.

Oilite is a trademark of Beemer Precision Incorporated.

Utility cart

Haul a variety of materials. Welded steel box construction.

Must order in multiples of two. The loaded weight of the cart should never exceed the weight of the tractor plus the operator.

LG265 home maintenance kit

Typical home maintenance kit

Home maintenance kits are a handy and convenient way for dealers to supply a customer with the maintenance-interval parts as specified in their operator's manual.

The LG265 home maintenance kit includes the following:

Rear deflector

The rear deflector installs in place of the collection hopper to discharge on the ground.

Compatibility Information

BM25065

For X350R.

Seat net kit

Seat net kit provides a convenient storage area for gloves, and other small items. It is available for open-back seats.

Supplemental lift-assist spring kit parts

The supplemental lift-assist spring kit is required for snow blower use on the X350R Rear-Discharge Tractor.

NOTE: The supplemental lift-assist kit is for use only when the snow blower is installed. It must be removed for installatiion of the rear-discharge mower deck.

Brush guard

The brush guard adds a distinctive appearance to the tractor and protects the front of the tractor from damage.

Brush guard lowered to permit opening hood

By removing one spring clip and pin, the brush guard may be lowered to permit opening the hood.

Compatibility Information

BM23057

For X300, X300R, X304, X305R, X310, X320, X534, and X540.

Front bumper

The front bumper adds a distinctive appearance to the tractor and protects the front of the tractor from damage.

Features include:

• Bumper can be easily mounted to the front of the tractor.
• Bumper can remain on the tractor when the front blade or snow blower are used.

Compatibility Information

BM23056

For X300, X300R, X304, X305R, X310, X320, and X534.

Kit includes two mower blades.

Mower deck leveling gauge

Leveling gauge allows quick and accurate mower deck leveling and cutting height adjustment.

Can be used for:

• Lawn tractors
• Lawn and garden tractors
• Riding mowers
• Front mowers
• Commercial walk-behind mowers
• Zero-turn-radius mowers

Mulch kit

Controls the clippings from blades and distributes more mulch.

Compatibility Information

BM25257

For X350R (SN -20,000).

14.1-kg (31-lb) wheel weight

One 14.1-kg (31-lb) plastic-shell rear wheel weight may be installed on each rear wheel to provide extra traction and stability.

Standard front bumper

Optional front weight bracket/bumper installed

The optional front weight bracket/bumper is available to replace the standard front bumper on the following tractors:

• Select Series™ X300, X300R, X304, X305R, X310, X320, X350, X350R, X354, X370, and X380 Tractors
• Model year 2007 and later (SN 020001-) Select Series model X500 Tractor
• All X530 Select Series Tractors
• Model year 2011 and later (SN 060001-) Select Series model X534 Tractor
• X570 Select Series Tractor

Front weight bracket/bumper with four weights

NOTE: Weights are ordered separately.

Holds up to four 19.1-kg (42-lb) Quik-Tatch weights:

• Provides an alternative to front-wheel weights for ballasting rear-mounted equipment
• Makes the 106.7-cm (42-in.) Hydraulic Tiller compatible with the X530 Tractor
• Functions as a bumper when weights are not installed

15.4-kg (34-lb) front wheel weight

A durable cast-iron weight can be mounted to each front wheel.

These weights are recommended for use when operating on slopes, especially when the tractor is equipped with a rear grass bagger or other rear-mounted equipment.

Each weight requires BM17978 mounting hardware.

Compatibility Information

BM17962

Requires BM17978 mounting hardware.

13.6-kg (30-lb) front-wheel weight shown

Hardware is required for installing each front-wheel weight.

Requirements:

• Mounting may require drilling two holes in the wheel rim.
• BM17978 mounting hardware kit is required for each weight.

NOTE: Front-wheel weights are not available for special-edition tractors because the styled front-wheel design does not have appropriate holes for mounting the wheel weights and no adapter is available.

Tire chain (optional wheel weights shown not included)

One pair of chains is included in each bundle.

Chains are recommended for extra traction when using attachments such as a snow blower or front blade.